大家在进行施工时要多加了解粉刷石膏这种装修材料的知识，以避免在装修是而出现的问题。那今天就由济南石膏粉小编为您在使用石膏粉过程中要遵守的标准，希望给您可以多注意一下。

Everyone should know more about the knowledge of plastering gypsum as a decoration material during construction, so as to avoid problems arising from decoration. Today, Jinan gypsum powder editor will provide you with the standards you should follow in the process of using gypsum powder. I hope you can pay more attention.

腻子粉是墙面找平材料，而这种找平是有要求的，一般情况下找平差不多超过3mm，在施工中，为了赶工期、省事，在墙体表面偏差大于3mm时，有些工人用腻子直接找平，由于目前室内墙面误差几乎都超过3mm而有的部位居然批刮达到1cm左右的厚度(局部)，这样问题就来了。

Putty powder is a wall leveling material, and this leveling is required. Generally, the leveling is almost more than 3mm. In order to speed up the construction period and save trouble, some workers use putty to level directly when the wall surface deviation is greater than 3mm. At present, the indoor wall surface error is almost more than 3mm, and some parts are scraped to a thickness of about 1cm (local), so the problem comes.

因为在涂刷乳胶漆或壁纸时，水分侵入，会融化腻子成膜层，在饰面层材料成膜收缩的时候，其腻子层中间也在发生收缩过程，批刮较厚的地方，收缩差异会很大，房间后期的水分挥发，会加快促使起皮、脱落的速度。所以腻子的批刮厚度一般不建议超过3mm，这一点也是腻子粉与腻子膏在使用年限与质量上存在差异的一个方面。

Because when painting latex paint or wallpaper, water intrusion will melt the putty into a film layer. When the film forming and shrinking of the facing layer material, the shrinkage process is also taking place in the middle of the putty layer. There will be a great difference in the shrinkage where the coating is thick. The water volatilization in the later stage of the room will accelerate the speed of peeling and falling off. Therefore, the scraping thickness of putty is generally not recommended to exceed 3mm, which is also an aspect of the difference between putty powder and putty paste in service life and quality.

因为腻子膏是工厂成品化生产，通过机械搅拌而成的，每一种原料的颗粒充分融合，含胶、含水量基本达到饱和，在工地施工时，挥发的只是水分，收缩比较均衡、密实度较高，而腻子粉的情况有所不同，成膜硬度、密实度都比较差，这也是腻子粉易出现起皮、脱落的原因所在。

Because the putty paste is produced in the factory through mechanical mixing, the particles of each raw material are fully integrated, and the glue and water content basically reach saturation. During construction on the site, only water is volatilized, with balanced shrinkage and high compactness. The situation of putty powder is different, and the film forming hardness and compactness are relatively poor, which is also the reason why putty powder is prone to peeling and falling off.

所以我们应该严格按照产品的施工流程来操作：

Therefore, we should strictly follow the construction process of the product:

1、将适量的水倒入容器，再加入腻子粉，然后用搅拌器充分搅拌至均匀无粉粒无沉淀的膏糊状；

1. Pour an appropriate amount of water into the container, then add putty powder, and then use the mixer to fully stir until the paste is uniform without powder particles and sedimentation;

2、用批刮工具进行批刮，待一层批嵌完成约4h后方可进行二道批刮；

2. Carry out batch scraping with a batch scraping tool, and carry out the second batch scraping after about 4h after the completion of the first layer of batch embedding;

3、将腻子层刮光滑，并控制厚度在1.5mm左右；

3. Scrape the putty layer smooth and control the thickness at about 1.5mm;

4、水泥基腻子完成自然养护到碱性与强度达到要求方可涂刷抗碱底涂料；

4. The alkali resistant primer can be applied only after the cement-based putty is naturally cured until the alkalinity and strength meet the requirements;

5、腻子层完成24h视温湿度状况进行浇水养护。

5. The putty layer shall be watered and cured according to the temperature and humidity conditions within 24h after completion.

以上的就是小编为朋友们详细的介绍了粉刷石膏在使用过程中的注意事项，希望您可以对此多加了解。当然有什么相关的问题解决不了的话，欢迎来我们网站//www.gochiism.com咨询客服。

The above is Xiaobian's detailed introduction to the precautions in the use of plaster for friends. I hope you can learn more about it. Of course, if you can't solve any related problems, welcome to our website //www.gochiism.com Consult customer service.