The internal and external corner is a professional term in decoration, which refers to the included angle between general wall and ceiling, concave internal corner, protruding external corner, and the included angle between external corner. The form is general wall and wall, and the line treatment method of internal and external corner is introduced in detail by Jinan putty factory as follows.

　　一、处理方法为阴阳线夹角法

　　1、 The treatment method is the angle between the internal and external lines1. 油漆

　　1. paint

　　当阴阳角绘画漆要保证平整,因为这必须提前有弹性的线,当绘画漆可以使用铝合金来依靠一边,另一边吹刮,如果想要耐用,阳角可以进行刷涂白水泥和石膏粉。

　　When the painting paint of internal and external corners should be smooth, because it must have elastic lines in advance. When the painting paint can rely on one side and the other side for blowing, if it wants to be durable, the external corners can be brushed with white cement and gypsum powder.

　　2. 壁纸

　　2. wallpaper

　　当壁纸阴阳角是更容易出现问题,阳角纸可以使用刮刀小心墙上贴壁纸,用手的凸角直折向下,然后用壁纸刀切,加上良好的胶棒,可以处理内部角从壁纸的凹角平的,外部与刮板上下移动贴墙,再好的墙纸。

　　When the internal and external corners of the wallpaper are the most likely to cause problems, the external corner paper can be pasted on the wall carefully with a scraper. The convex corners of the hand can be folded straight down, and then cut with a wallpaper knife. With a good glue bar, the internal corners can be treated as flat from the central concave corners of the wallpaper. The external and scraper can be moved up and down to paste the wall, and then the good wallpaper can be pasted.

　　3.贴瓷砖

　　3. tiles

　　贴瓷砖时，墙面阴阳角处理是更困难的。更常见的方法是用瓷砖本身来拼接，瓷砖边缘用切割机或手工切割成45度角，这样贴出的角度更圆润美观。

　　When tiling, the treatment of internal and external corners of the wall is the most difficult. The more common method is to use the tile itself to splice, and the edge of the tile is cut into 45 degree angle with a cutting machine or by hand, so that the angle pasted out is more round and beautiful.

　　二、处理墙壁阴阳角度的注意事项:

　　2、 Precautions for dealing with the internal and external angles of the wall:

　　1. 批灰处理

　　1. Batch ash treatment

　　先对基层灰进行批量处理，然后用刮刀对反弹线进行刮削，使其与周围的阴阳角和凸块都干净，避免出现反弹线不直的情况。

　　First, the base ash is treated in batches, and then the rebound line is scraped with a scraper to make it clean with the surrounding internal and external corners and bumps, so as to avoid the situation that the rebound line is not straight.

　　2. 弹性线处理

　　2. Elastic line treatment

　　在处理墙上的阴阳角线时，一定不能忽略弹性线。在每个垂直阴阳角,垂直线应该下降了的线弹性线治疗,和一个平行的线平行的垂直线阴阳角应放置的位置500毫米双方基于阴阳角的垂直线。墙面吹腻子前，用石膏对阴阳角两侧用500毫米内进行找平，找平误差不超过2毫米为准确。

　　When dealing with the internal and external corners of the wall, elastic lines must not be ignored. In each vertical internal and external corner, the vertical line should be lowered by the linear elastic line treatment, and the internal and external corners of the vertical line parallel to a parallel line should be placed at 500mm based on the vertical line of the internal and external corners. Before puttying the wall, plaster the two sides of the internal and external corners within 500mm, and the leveling error shall not exceed 2mm.

　　3、刷腻子

　　3. Apply putty

　　沿着弹性线用腻子将阴阳角直,等干后打开满是灰,然后由铝合金统治者从阴角阳角,来来回回,为了避免阴角不直,阴阳角完成后注意检查,一般在5毫米误差是正常范围,超过5毫米石膏找平处理。

　　Use putty to straighten the internal and external corners along the elastic line, open it to be full of ash after drying, and then the aluminum alloy ruler will come and go back from the internal and external corners. In order to avoid the internal and external corners are not straight, pay attention to the inspection after the completion of the internal and external corners. Generally, the 5mm error is the normal range, and the gypsum is more than 5mm for leveling.

　　4. 抗爆处理杨角

　　4. Anti explosion treatment of Yangjiao

　　墙面阴阳角线完成处理后做好保护,因为阳角是凸,所以更危险,注意抗爆阳角处理,可使阳角光滑,用砂纸打磨或安装角的保护,这是一个很好的方式来保护阳角。

　　Protect the internal and external corners of the wall after finishing the treatment, because the external corners are convex, so it is more dangerous. Pay attention to the anti explosion external corners treatment, which can make the external corners smooth. Use sandpaper to polish or install the protection of the angle, which is a good way to protect the external corners.

　　以上是济南腻子粉厂家为大家介绍的相关内容，想要了解更多内容，欢迎访问网站：//www.gochiism.comThe above is the relevant content introduced by Jinan putty powder manufacturer. To learn more, please visit the website: //www.gochiism.com