I. Installation Technology of Gypsum Line

　　1. 清洗:安装抹灰线前，应清理安装现场的腻子粉和灰尘。有些难以清洁的物质可以用水辊涂上一层水，然后用铲子清理干净。这样可以保证石膏线安装更加牢固，避免石膏线在以后出现脱落的现象。

　　1. Cleaning: Putty powder and dust should be cleaned up before plastering line is installed. Some substances that are difficult to clean can be coated with water rollers and cleaned with shovels. This can ensure that the installation of gypsum line is more solid, and avoid the phenomenon of gypsum line falling off in the future.

　　2. 油漆墨线:清洁灰尘后，将墨线与墨桶一起涂在墙面上。但在墙面顶角处用一段线条用力轻轻画出，量出墙体的长度，将决定石膏线的长度和宽度。

　　2. Paint ink line: After cleaning the dust, paint the ink line and ink bucket on the wall together. But the length and width of the gypsum line will be determined by measuring the length of the wall by gently drawing a line at the top corner of the wall.

　　3.石膏线切割:确定石膏线长度后，切割石膏线。再剪两端，就可以把膏药线放上去，按45度已婚女性剪两端。

　　3. Gypsum wire cutting: After determining the length of the gypsum wire, cut the gypsum wire. Cut both ends, you can put the plaster line on, according to 45 degrees married women cut both ends.

　　4. 石膏粉治疗:石膏粉和水以一定比例混合,均匀涂抹它两边的石膏线条,然后使石膏行充裕的下缘的位置墨,拿了几分钟,然后用混合石膏粉填充头部。

　　4. Gypsum powder treatment: mix gypsum powder and water in a certain proportion, evenly smear the gypsum lines on both sides of it, then make the gypsum line abundant lower edge position ink, take a few minutes, and then fill the head with mixed gypsum powder.

　　二世。注意事项

　　King II. Matters needing attention

　　1. 基本治疗。石膏线施工前应清理基层，墙面应平整，无凸凹部位。墙顶角的地方，会吹腻子两次。这将防止石膏线脱落。

　　1. Basic treatment. Before the construction of gypsum line, the base should be cleaned up, the wall surface should be flat and there should be no convex and concave parts. Putty will be blown twice at the top corner of the wall. This will prevent the gypsum line from falling off.

　　2. 石膏线在施工中，要从正面开始，这样才能保证石膏线的正节理部分更少，使石膏线的整体效果看起来更流畅。将不足一半的关节或需要的关节放置在未标记的区域。

　　2. In the construction of gypsum line, it is necessary to start from the front, so as to ensure that there are fewer normal joints of gypsum line and make the overall effect of gypsum line look smoother. Place less than half of the joints or required joints in unmarked areas.

　　3.由于石膏的凝结时间相对较短，所以在安装石膏线时，需要快速粘贴和调整，并迅速补上有缺陷的部分。打石膏前一定要用水清洗边缘。

　　3. Because the setting time of gypsum is relatively short, it is necessary to paste and adjust quickly when installing gypsum line, and fill the defective parts quickly. Clean the edges with water before plastering.

　　4. 在石膏线的接缝处，必须刮掉石膏后才能进行对接。对接时应注意花纹与纹理的匹配，高度一致。使石膏线整体呈直线，下部应采用石膏垫直，以免石膏出现断线的问题。石膏线安装后，应及时用清水清洗干净，以免石膏凝固，污渍无法清洗，从而影响石膏线的整体美观程度。

　　4. At the joint of the gypsum thread, the gypsum must be scraped off before the joint can be made. When docking, attention should be paid to the matching of pattern and texture, which is highly consistent. In order to make the gypsum line straight as a whole, the lower part should be upright with gypsum pad in order to avoid the problem of broken line in gypsum. After installation of gypsum line, it should be cleaned with clear water in time to avoid gypsum solidification and stain can not be cleaned, thus affecting the overall aesthetic level of gypsum line.

　　5. 石膏线修复过程中，将石膏线粘贴后，对石膏线接缝部位进行修复，以稀释石膏线接缝部位。对墙面进行修复，保证石膏线出墙的部位宽度一致。

　　5. In the process of repairing the gypsum thread, after pasting the gypsum thread, the joint of the gypsum thread is repaired to dilute the joint of the gypsum thread. Repair the wall surface to ensure that the width of the gypsum line out of the wall is the same.