嵌缝石膏是由天然或合成的油脂等为基料，同碳酸钙、滑石粉等矿物掺合，形成高黏度的塑性膏状物，一般在氧化后表面成膜并随时间延续氧化深入内部而逐渐硬化。嵌缝石膏具有明显的塑性，可用手或刮刀嵌填腻缝，成本低，施工方便。

Caulking gypsum is a high viscosity plastic paste made from natural or synthetic fats as the base material, mixed with minerals such as calcium carbonate and talc powder, to form a film on the surface after oxidation and gradually harden over time. Caulking gypsum has obvious plasticity and can be used to fill greasy joints by hand or scraper, with low cost and convenient construction.

嵌缝石膏和腻子的凝结速度和主要作用不同，嵌缝石膏比腻子的凝结速度慢，不容易打磨，通常用来做基层处理，填平裂缝;腻子主要用于普通水泥墙面刷乳胶漆前的打底。

The setting speed and main function of caulking gypsum and putty are different. The setting speed of caulking gypsum is slower than that of putty, and it is not easy to polish. It is usually used for base treatment and filling cracks; Putty is mainly used for priming ordinary cement walls before applying latex paint.

济南嵌缝石膏的施工方法是怎样的？

What is the construction method for Jinan caulking gypsum?

1、调配嵌缝石膏

1. Mix caulking gypsum

准备一个干净的桶和搅拌器，桶里加入适量的水的，然后加入粉放置几分钟后搅拌均匀，达到可以施工的粘稠度即可。

Prepare a clean bucket and mixer, add an appropriate amount of water to the bucket, then add powder and let it stand for a few minutes before stirring evenly until the viscosity that can be applied is reached.

2、接缝施工

2. Joint construction

将搅拌好的材料均匀地刮在板缝处，厚度约2mm，将接缝纸带压入湿料中，用刮刀或批刀批平。

Evenly scrape the mixed material onto the seam of the board, with a thickness of about 2mm. Press the seam paper strip into the wet material and use a scraper or screwdriver to level it.

3、养护装饰

3. Maintenance decoration

接缝部位的嵌缝石膏完全干燥后，就可以进行后续的装饰了。

After the caulking gypsum at the joint is completely dry, subsequent decoration can be carried out.

腻子的施工方法的怎样的？

What is the construction method for putty?

1、准备工具

1. Prepare tools

腻子施工重要的就是平整均匀，一般会使用到刮板，省时省力，用起来也很方便。

The important thing for putty construction is that it is flat and uniform. Generally, a scraper is used, which saves time and effort, and is also very convenient to use.

2、墙面基层处理

2. Wall base treatment

墙面刮腻子首先要处理基层，如果是老旧的墙面，已经出现起皮、脱落、开裂的情况，要把墙面的墙皮清理干净，较大的裂缝填补平整，才可以进行后续的腻子施工。

To apply putty on the wall, the first step is to treat the base layer. If an old wall has already peeled, peeled off, or cracked, the wall surface must be cleaned and the larger cracks filled flat before proceeding with subsequent putty construction.

3、腻子粉施工

3. Putty powder construction

在水桶先加适量的水，将腻子倒入桶内，用搅拌器搅拌均匀。然后放置几分钟再开始施工，保证腻子和水融合的程度更高。用刮板蘸取腻子直线涂抹或呈扇形弧度刮,用刮板蘸取腻子直线涂抹或呈扇形弧度刮涂，将腻子压平即可。一般腻子要刮涂两遍，上一遍干燥后才能进行下一层的刮涂，刮涂两遍后待腻子晾干，再进行打磨处理，将墙面上不平整的地方打磨平整。

Add an appropriate amount of water to the bucket first, pour the putty into the bucket, and stir evenly with a mixer. Then let it sit for a few minutes before starting construction to ensure a higher degree of fusion between the putty and water. Use a scraper to dip the putty in a straight line or in a fan-shaped arc, then use a scraper to dip the putty in a straight line or in a fan-shaped arc, and press the putty flat. Generally, putty needs to be applied twice, and the previous layer should be dried before the next layer can be applied. After applying twice, the putty should be allowed to dry before polishing to smooth out any uneven areas on the wall.

4、注意事项

4. Precautions

墙面腻子的施工对温度是有要求的，寒冷的冬季尽量避免施工，会影响施工效果。腻子刮涂完成后，要进行适当养护，短时间内不要碰水。您对此还有什么需求就来我们网站//www.gochiism.com咨询吧！

The construction of wall putty has temperature requirements, and construction should be avoided as much as possible in cold winter, as it may affect the construction effect. After the putty is scraped and applied, appropriate curing should be carried out and water should not be touched for a short period of time. If you have any further needs regarding this, please come to our website //www.gochiism.com Consult!