Jinan putty powder you may have heard, but some people may still ask: what is putty powder. As a kind of grass-roots building materials, its use is very wide, so what impact does it have on the grass-roots materials? Today, Jinan Fuhua building materials analyzes this problem for you.

所谓腻子粉腻子又称为填泥，属于一种厚浆状涂料。涂施于底漆上或直接涂施于物体上，用以清除被涂物表面上高低不平的缺陷。

The so-called putty powder putty, also known as filling mud, belongs to a thick paste coating. It can be applied on the primer or directly on the object to remove the uneven defects on the surface of the object to be coated.

济南腻子粉

Jinan putty powder

它由少量的漆基、大量的填料和适量的着色颜料制成。使用的颜料主要是铁红、炭黑、铬黄等。填料主要是重质碳酸钙、滑石粉等。它可以用局部凹陷填充工作表面或刮掉整个表面。通常在底漆层完全干燥后，将其涂在底漆层的表面。

It is made of a small amount of lacquer base, a large amount of filler and an appropriate amount of pigment. The main pigments used are iron red, carbon black, chrome yellow, etc. The main fillers are heavy calcium carbonate, talc, etc. It can fill the working surface with local depressions or scrape off the whole surface. It is usually applied to the surface of the primer after it has completely dried.

现象：施工完成并仔细干燥后，用手触摸会掉粉。

Phenomenon: after the construction is completed and carefully dried, the powder will drop when touching with hands.

济南腻子粉产生这种现象的原因：

The reasons for this phenomenon are as follows

1、内墙腻子粉抛光时间不好，表面已经干燥，然后抛光处理将去除粉末;

1. The internal wall putty powder polishing time is not good, the surface has been dry, and then polishing will remove the powder;

2、外墙腻子粉饰面时涂层相对较薄。夏季高温条件下，水分挥发快，表层水分不足无法固化，因此容易脱粉。

2. The coating of exterior wall putty powder is relatively thin. Under the condition of high temperature in summer, the moisture volatilizes quickly, and the surface moisture is insufficient to solidify, so it is easy to remove the powder.

3、产品超过保质期，粘接强度大大降低。

3. The adhesive strength of the product is greatly reduced when it exceeds the shelf life.

4、产品储存不当会大大降低吸湿后的附着力。

4. Improper storage of products will greatly reduce the adhesion after moisture absorption.

5、基层的高吸水率导致腻子快速干燥，没有足够的水来固化。

5. The high water absorption of the base causes the putty to dry quickly and there is not enough water to cure.

解决方法：

resolvent:

济南腻子粉

Jinan putty powder

1、抛光内壁腻子表面时，应掌握合适的抛光时间。抛光时间是在水印消失后立即抛光腻子表面。实践证明，1~2m2的单板应平整或打磨。

1. When polishing the surface of inner wall putty, the appropriate polishing time should be mastered. The polishing time is to polish the putty surface immediately after the watermark disappears. Practice has proved that 1 ~ 2M2 veneer should be flat or polished.

2、外墙腻子表面干燥后，应适当打磨，并充分浇水湿润。一般维护应分为两次或两次以上。如有必要，请用透明封闭底漆兑水(1：5)作为二道淋水液，效果会更好。

2. After the surface of external wall putty is dry, it should be properly polished and fully watered. General maintenance should be divided into two or more times. If necessary, use the transparent sealing primer mixed with water (1:5) as the second spray, the effect will be better.

3、产品需要在保修期内使用。超过保修期时，需要进行试刮，检查合格后方可施工。

3. The product needs to be used within the warranty period. When the warranty period is over, trial scraping shall be carried out, and construction can only be carried out after the inspection is qualified.

4、产品需要注意防水处理，应存放在阴凉干燥的地方，并保证封装完好。

4. Products need to pay attention to waterproof treatment, should be stored in a cool and dry place, and ensure good packaging.

5、在夏季或高温大风气候下，涂抹腻子前要先用清水湿润墙面，待墙面无明水后再涂抹腻子

5. In summer or high temperature and gale climate, before applying putty, wet the wall with clean water, and then apply putty when there is no clear water on the wall

以上就是济南腻子粉对基层材料影响的简介了，希望能够对您有所帮助。如果大家对于还想了解更多的关于建筑材料的知识，或者其相关产品知识，欢迎前来我们的网站咨询，我们将竭诚为您服务。

The above is the brief introduction of the influence of Jinan putty powder on the base material, hoping to help you. If you want to know more about building materials, or its related product knowledge, welcome to our website, we will serve you wholeheartedly.